FW 10 is fertig...

Solyth

Well-known member
Mitglied seit
Jan 25, 2013
Beiträge
1.661
www.fractalaudio.com/downloads/firmware-presets/axe-fx-3/10p0/axefxiii_dsp_rel_10p00.zip

10.00

Added Downtune control to Tuner. The Downtune control allows for simplified tuning when tuning down one to four semitones. The Tuner display will read the “natural” name of the note, i.e. if tuning down one semitone an Eb will read E. In addition any blocks that utilize pitch information will also be transposed accordingly.

Added Display Mode control to Tuner. This control allows selecting between all flats, all sharps or a mixture of sharps/flats for the displayed note name.

New power amp modeling algorithm. This algorithm improves the plate impedance accuracy substantially. This yields tighter bass, crunchier midrange and “chimier” highs.

Due to the changes in the power amp modeling algorithm the Power Tube Hardness parameter now behaves differently. Selecting a Power Tube Type loads the “knee voltage” for the power tubes and this voltage can be adjusted up or down using Power Tube Hardness. Higher values yield a lower knee voltage and more abrupt clipping and vice-versa. Existing presets will have Power Tube Hardness reset to 5.0 upon recall.

The range of the Transformer Match control has been reduced to 0.5 to 2.0. Existing presets will have this value reset to 1.0.

The Ideal Tetrode and Ideal Pentode power tube models are no longer applicable and have been replaced with 5881 and 6L6GB models, respectively.

The PI Bias Excursion values have been updated for some amp models. Existing presets will automatically be updated to the new default values. If you typically alter this parameter you should audition your presets.

The Amp block Dynamic Impedance parameter is no longer applicable and has been removed.

Added KT77 power tube type.

Improved Drive block. New diode modeling algorithm improves clipping accuracy especially for diodes with higher saturation currents, i.e. 1N270 and other germanium types.

Added D9E and D18 diode models to Drive block. These are Soviet germanium diodes valued for their smooth distortion characteristics.

Added “Ruckus LED/Si” type to Drive block. This model is based on a Suhr Riot with the toggle switch set to select the hybrid LED/Silicon Diode position.

Added “5 Band Mark” type to Graphic EQ block.

Fixed exported Tone Matches may, in rare cases, not sound the same as the Tone Match.

Fixed long delay times (over 1.5 seconds) in Plex Shift can cause artifacts.
 

Solyth

Well-known member
Mitglied seit
Jan 25, 2013
Beiträge
1.661
Hab sie grad mal probiert.
Lässt sich irgendwie schwer beschreiben, wie monstergeil:hail::hail::hail: der Sound jetzt ist....
nur so viel, die FW lohnt sich so richtig:biggrin::bounce::biggrin:
 

axifist

Well-known member
Mitglied seit
Nov 14, 2013
Beiträge
1.921
Er hat wieder einen neuen Modelling-Algorithmus entwickelt, den er "FASPICE XD" nennt. Klingt wohl sauberer, wenn man extreme Einstellungen macht. Braucht mehr Rechenleistung, daher könnte das endgültig nicht mehr auf das II portiert werden. Naja, schauen wir mal ;)
 

Friedlieb

Well-known member
Axe-Fest 2023 Teilnehmer
Axe-Fest 2020 Online Teilnehmer
Axe-Fest 2019 Teilnehmer
Axe-Fest 2018 Teilnehmer
Axe-Fest 2017 Teilnehmer
Mitglied seit
Sep 29, 2012
Beiträge
1.396
Ja, ich finde das Update auch richtig klasse. Jetzt hört man noch besser meine Spielfehler.
 

aalrh

Administrator
Teammitglied
Axe-Fest 2023 Teilnehmer
Axe-Fest 2022 Teilnehmer
Axe-Fest 2020 Online Teilnehmer
Axe-Fest 2019 Teilnehmer
Axe-Fest 2018 Teilnehmer
Axe-Fest 2017 Teilnehmer
Mitglied seit
Sep 29, 2012
Beiträge
3.437

Friedlieb

Well-known member
Axe-Fest 2023 Teilnehmer
Axe-Fest 2020 Online Teilnehmer
Axe-Fest 2019 Teilnehmer
Axe-Fest 2018 Teilnehmer
Axe-Fest 2017 Teilnehmer
Mitglied seit
Sep 29, 2012
Beiträge
1.396
Eigentlich ist es gut. Ich persönlich möchte gern das schwächste Glied in der Kette sein. Das Equipment sollte so gut sein, dass ich keinen Vorwand mehr habe. Nur dann strengt man sich richtig an. IMHO. :)
 

Hamsworld

Well-known member
Mitglied seit
Feb 12, 2014
Beiträge
1.932
10.01 ist auch draußen.

10.01
Fixed divide-by-zero can happen in Drive block when using certain combinations of different diode types and a very strong input signal or when switching between different types.
Fixed can’t access Drive block Advanced GUI page for Ruckus LED/Si type.
Changed Drive block Slew Limit to Slew Rate and updated default value of the models. Existing presets will be updated to the new default value upon recall. Note that the parameter now controls the slew rate and lower values equal less high frequency response at high amplitudes and vice-versa (the action is reversed from the previous firmware versions).
Added Wrecker Express Bright amp model. This models the amp with the three-position Bright switch in the down position.

Ist wirklich toll. Selbst die Werkspresets blühen auf. Man kan es nicht anders sagen. Fuchs ODS, die Fender-Amps, 1959 Plexi - klingt alles echt toll. Mit schönen Höhen übrigens!
 

Hamsworld

Well-known member
Mitglied seit
Feb 12, 2014
Beiträge
1.932
Uuuuuuunnnnd 10.02.

Release Notes:

10.02
Fixed popping noise can occur when switching between certain amp models. This also results in faster, smoother preset, scene and channel changes.

Fixed wrong Basic tab of Drive block when Ruckus LED/Si type selected.

Added Wrecker Liverpool Bright amp model. This models the amp with the three-position Bright switch in the brightest position.


Cooles Feature seit einiger Zeit (hatte ich gar nicht mitgekriegt:) Fractal-Bot ist in Axe Edit integriert.
 

Arni61

Member
Mitglied seit
Aug 5, 2019
Beiträge
98
Kann es sein, dass aufgrund der letzten größeren Updates ( ab 9.0) manche ältere Presets nicht mehr so funktionieren wie sie mit 5.0 erstellt wurden? Manche Blöcke ( Delay, Rotary) wechseln bei den Scenen nicht mehr und bleiben übergreifend
bestehen. Geht mir so bei manchen Brett Kinman Presets.
 
Oben
mainframe-fourhanded
mainframe-fourhanded