11.01 ist raus.
http://www.fractalaudio.com/downloads/firmware-presets/axe-fx-3/11p0/axefxiii_dsp_rel_11p01.zip
11.01
Updated Speaker Impedance Curves for 2x12 Jazz 120, 4x10 Brit JM45 and 4x12 Hipower. Also added the following new curves: 2x12 Bassbuster (based on a Fender Bass Breaker) 1x12 Tweed Alnico Blue (based on a Fender Deluxe with Celestion Blue) 4x12 PVH 6160 (based on a Peavey 5150 w/ Sheffields) 4x12 Euro (based on a Bogner standard) 2x12 Recto (based on a Mesa Rectifier)
Added “Matchbox D-30 EF86” amp model. While the real amp has a six-position Tone switch, the model has a continuously variable tone control. Note that the Tone control is mapped to the Bass control in Ideal mode as the Tone switch is essentially a bass cut control.
11.00
Amp block now uses new high-order speaker impedance modeling. 52 speaker impedance models (and two LB-2 models) are included and can be selected using the Speaker Impedance Curve parameter (on the Advanced page). Selecting an amp model will load an appropriate default Speaker Impedance Curve for that amp model. The Cabinet Resonance parameter can be used to adjust the amount of cabinet resonance in the impedance curve. NOTE: The 2x12 Bassguy, 2x12 Jazz 120, 4x10 Brit JM45 and 4x12 Hipower data is incomplete and will be updated in a future release.
Setting Global “Update Pre-11.x Presets Spkr Imp Upon Load" parameter to YES will automatically update the Speaker Impedance Curve for the Amp blocks upon preset recall to use an appropriate Speaker Impedance Curve for that amp model. Setting the parameter to NO will leave existing presets unaffected. NOTE: Setting this to YES will also cause the EDITED LED to light indicating the preset has been modified.
Fixed Recto1/2 models default Negative Feedback and Power Tube Bias values slightly too low.
Fixed loss of precision in Drive block Tone control for some models (Rat, Timothy, et. al.) causing low frequency build-up over time.
http://www.fractalaudio.com/downloads/firmware-presets/axe-fx-3/11p0/axefxiii_dsp_rel_11p01.zip
11.01
Updated Speaker Impedance Curves for 2x12 Jazz 120, 4x10 Brit JM45 and 4x12 Hipower. Also added the following new curves: 2x12 Bassbuster (based on a Fender Bass Breaker) 1x12 Tweed Alnico Blue (based on a Fender Deluxe with Celestion Blue) 4x12 PVH 6160 (based on a Peavey 5150 w/ Sheffields) 4x12 Euro (based on a Bogner standard) 2x12 Recto (based on a Mesa Rectifier)
Added “Matchbox D-30 EF86” amp model. While the real amp has a six-position Tone switch, the model has a continuously variable tone control. Note that the Tone control is mapped to the Bass control in Ideal mode as the Tone switch is essentially a bass cut control.
11.00
Amp block now uses new high-order speaker impedance modeling. 52 speaker impedance models (and two LB-2 models) are included and can be selected using the Speaker Impedance Curve parameter (on the Advanced page). Selecting an amp model will load an appropriate default Speaker Impedance Curve for that amp model. The Cabinet Resonance parameter can be used to adjust the amount of cabinet resonance in the impedance curve. NOTE: The 2x12 Bassguy, 2x12 Jazz 120, 4x10 Brit JM45 and 4x12 Hipower data is incomplete and will be updated in a future release.
Setting Global “Update Pre-11.x Presets Spkr Imp Upon Load" parameter to YES will automatically update the Speaker Impedance Curve for the Amp blocks upon preset recall to use an appropriate Speaker Impedance Curve for that amp model. Setting the parameter to NO will leave existing presets unaffected. NOTE: Setting this to YES will also cause the EDITED LED to light indicating the preset has been modified.
Fixed Recto1/2 models default Negative Feedback and Power Tube Bias values slightly too low.
Fixed loss of precision in Drive block Tone control for some models (Rat, Timothy, et. al.) causing low frequency build-up over time.